Printing from the screen is one of the most efficient techniques when it comes to print. One can use it on silk, paper, and many more products. Though the activity seems natural, this is not the case and here are some challenges that you might face when doing Maryland screen printing and the ways that you can manage them.
If you notice that the paint is spreading through the areas that you do not want to print, then this is known as bleeding. It is one of the most common mistakes that one might find, and the best way that you can deal with it is making the paste thick. Bleeding comes as a result of using watery paste. It is best to ask someone who has been this for a long time to help you with the mixing of the adhesive.
One might also end up with a situation where they have different gaps left between the repeats. The condition might only take place if the registration is not calculated. Thus, it is advisable to check the holes before doing the repeats.
At times, no matter how much one calculates, they still find that they have issues with the repeat. As a way to deal with this, it is best to mark the cloth so that you can be sure where you will do the placing. You can also make use of colored strands at the edge so that you can know exactly where to place the tensile.
The other thing that you should watch out for is soiling of the cloth. Note that if you do not block the pores, then you might end up with this problem. That is the reason that you should apply a tape around the edge; it will make the print clean and well done since there will be no spillage on the sides.
If the colored pigments are not distributed evenly on the tensile, then there could be the formation of color patches. That is the reason that enough pigments need to be used so that the paste can end up being evenly distributed and thus prevent any patchy effects. At the same time, the pulling of the squeegee should be well done.
Pinholes are another issue that you might face, and the worst part is that no matter how many times you do the repeat they do not go away. This leaves your print looking untidy. One of the reasons that you might face a pinhole is if you do not clean up the mesh. It is important to get rid of any impurities before you start the printing so that you can end up with ideal results.
If you do not do the coating right then, this is another reason that you will end up with pinholes. That is the reason that it is advisable to carry out the surface more than ones. That way when you do the final washing on the fabric, the colors will be well distributed, and you will not have to deal with pinholes.
If you notice that the paint is spreading through the areas that you do not want to print, then this is known as bleeding. It is one of the most common mistakes that one might find, and the best way that you can deal with it is making the paste thick. Bleeding comes as a result of using watery paste. It is best to ask someone who has been this for a long time to help you with the mixing of the adhesive.
One might also end up with a situation where they have different gaps left between the repeats. The condition might only take place if the registration is not calculated. Thus, it is advisable to check the holes before doing the repeats.
At times, no matter how much one calculates, they still find that they have issues with the repeat. As a way to deal with this, it is best to mark the cloth so that you can be sure where you will do the placing. You can also make use of colored strands at the edge so that you can know exactly where to place the tensile.
The other thing that you should watch out for is soiling of the cloth. Note that if you do not block the pores, then you might end up with this problem. That is the reason that you should apply a tape around the edge; it will make the print clean and well done since there will be no spillage on the sides.
If the colored pigments are not distributed evenly on the tensile, then there could be the formation of color patches. That is the reason that enough pigments need to be used so that the paste can end up being evenly distributed and thus prevent any patchy effects. At the same time, the pulling of the squeegee should be well done.
Pinholes are another issue that you might face, and the worst part is that no matter how many times you do the repeat they do not go away. This leaves your print looking untidy. One of the reasons that you might face a pinhole is if you do not clean up the mesh. It is important to get rid of any impurities before you start the printing so that you can end up with ideal results.
If you do not do the coating right then, this is another reason that you will end up with pinholes. That is the reason that it is advisable to carry out the surface more than ones. That way when you do the final washing on the fabric, the colors will be well distributed, and you will not have to deal with pinholes.
About the Author:
Find a summary of the advantages you get when you use Maryland screen printing services and more information about a reputable printing company at http://spnprints.com/services.html now.
0 commentaires:
Post a Comment